Have a large project? Request a Quote Now. 100% USA Made Epoxy

Metallic Epoxy - 70 SQ FT KIT

Our metallic epoxy 70 Sq Ft kit is awesome for resurfacing your countertops or floor. It's our best seller! It's all about being creative and making a room come together. This kit comes with a 3/4 gallon kit of HD Pro, a 3/4 gallon kit of Clear100, C ...
  • $325.74

  • $365.00

Available Options

VIDEO AND INSTRUCTIONS
FOOD SAFE and 100% AMERICAN MADE
DURABLE, UV AND HEAT RESISTANT
LARGE PROJECT? GET A QUOTE
MADE FRESH / LOW VOC ON MOST PRODUCTS

Our metallic epoxy 70 Sq Ft kit is awesome for resurfacing your countertops or floor. It's our best seller! It's all about being creative and making a room come together. This kit comes with a 3/4 gallon kit of HD Pro, a 3/4 gallon kit of Clear100, Consider waste and extra colors... If your project is 70 sq ft and your design includes 3 colors, consider purchasing more CLEAR100 metallic binder. You have to figure in waste as well. Adding more colors will always use more epoxy. Upgrade your kit to either an extra quart kit or a 3/4 gallon kit of CLEAR100. Perhaps upgrade to our 150 sq ft kit to ensure you have enough epoxy for your project. You can also purchase a 3/4 gallon ribbon kit. Which includes a 4oz pigment, and a 3/4 gallon kit of CLEAR100. 

We highly recommend getting a second metallic powder if you are wanting to add a highlight color to your surface. Also if you are looking to add highlights, instead of splitting this kit, you could just purchase an extra quart or 3/4 gallon kit within this product! You will see an option that says - add more clear to your kit. You can select a quart kit or a 3/4 gallon kit. Compare this kit to any of our competitor's price ($600 TO $800). Why so reasonably priced? We are the manufacturer, theirs no middle man like other websites selling epoxy. Our metallic pigments for this kit come in 4-ounce containers. Each 45 gram pouch is good for 1 gallon of clear binder SPE-META-UV. 

Wondering about the base color? Simply choose the closest color to the most dominant color that you want your countertop to look like. The base really can't be seen. It will enhance the metallics. For example, if you choose Pearl White, choose off-white or white as your base. 


If you are looking to add a highlight color we highly recommend purchasing the 3/4 gallon ribbon kit within the configurable options. Which includes a 3/4 gallon kit of CLEAR100 and a 4oz pigment of your choice.


Faster Shipping on the following colors:

• White

• Medium Gray

• Black


If you are looking for a highlight color, you must buy a second color. You can purchase the second color above or Click here to buy more metallic pigments. 


What's Included?

• 3/4 Gallon Base / HD PRO - 93% Solids (Part A and Part B)

• 1 - 3/4 Gallon Kit of CLEAR100 Epoxy (Binder for Metallic Pigments) (Part A and Part B)

• 1 Quart Kits of CLEAR100 / Epoxy (Binder for Metallic Pigments) (Part A and Part B)

• 1 - 4oz Metallic Pigment of your choice. Use 3oz for 3/4 gallon kit, and 1oz for quart kit of CLEAR100. 


Tools Not Included, but highly recommended. You can find them in our store by clicking on the links below:

12" Flat Squeegee

Oval Mixer designed to remove air from mixtures


NEW! YOU CAN NOW PURCHASE A 1OZ METALLIC PIGMENT INSTEAD OF BUYING A LARGE 4OZ CONTAINER! YOU CAN ALSO PURCHASE OUR SPARKLE ADDITIVE BY THE OZ. 1OZ JUST $8 BUCKS!


Pro Tip: If you would like to add a 3rd metallic pigment, buy a quart kit of our metallic binder here. All of our epoxies can be purchased in the by layers section. You can build your own kit if you like. 

Preparation, Mixing and Installation Instructions for Primer / Base - HD PRO High Solids System. This kit includes HD PRO, our superior and most versatile base system. 


1) PRODUCT STORAGE: Store product in an area so as to bring the material to normal room temperature before using. Continuous storage should be between 60 and 90 degrees F. Low temperatures or great temperature fluctuations may cause crystallization.


2) SURFACE PREPARATION: The most suitable surface preparation would be a fine brush blast (shot blast) to remove all laitance and provide a suitable profile. All dirt, foreign contaminants, oil, and laitance must be removed to assure a trouble free bond to the substrate. A test should be made to determine that the substrate (Concrete, Laminate, Tile, Formica, MDF, etc) is dry; this can be done by placing a 4’X4’ plastic sheet on the substrate and taping down the edges. If after 24 hours, the substrate is still dry below the plastic sheet, then the substrate is dry enough to start coating. The plastic sheet testing is also a good method to determine if any hydrostatic pressure problems exist that may later cause dis-bonding.


3) PRODUCT MIXING: This product has a mix ratio of 12# part A to 3.85# part B for standard colors. Standard packages are in pre-measured kits and should be mixed as supplied in the kit. We highly recommend that the kits not be broken down unless suitable weighing equipment is available. After the two parts are combined, mix well with slow speed mixing equipment such as a jiffy mixer until the material is thoroughly mixed and streak free. After mixing, transfer the mixed material to another pail (the transfer pail) and again remix. The material in the transfer pail is now ready to be applied on the primed substrate. Improper mixing may result in product failure.


4) PRIMING: This product is only intended as a high solids primer suitable for most substrates. However, if the surface is very porous, then a lower solids primer might be more suitable to reduce the possibility of air release problems occurring. Contact your Spartan Epoxies sales rep for more information.


5) PRODUCT APPLICATION: The mixed material can be applied by brush or roller. However, the material can also be applied by a suitable serrated squeegee and then back rolled as long as the appropriate thickness recommendations are maintained. Maintain temperatures and relative humidity within the recommended ranges during the application and curing process. If concrete conditions or over aggressive mixing causes air entrapment, then an air release roller tool should be used prior to the coating tacking o to remove the air entrapped in the coating. Thinner applications will not level as well as higher build applications.


6) RECOAT OR TOPCOATING: Although a topcoat is recommended, it is optional. Many topcoats are suitable for placement over this coating including both urethanes and epoxies. When top coating this product, you must first be sure that the coating has tacked o before top coating can commence. Before top coating, check the coating to verify no epoxy blushes were developed (a whitish, greasy film or de-glossing). If a blush is present, it must be removed prior to top coating. A standard type detergent cleaner can be used to remove any blush. Many epoxy coatings and urethanes are compatible for use as a topcoat for this product as well as multiple coats of this product as an intermediate build coat.


7) CLEANUP: Xylol is the most effective, but if you wish not to use xylol, you can use acetone or alcohol. Xylol is the best and most recommended. Remember to protect your skin and eyes.


8) CLEANING: Caution! Some cleaners may affect the color of the epoxy installed. Test each cleaner in a small area, utilizing your cleaning technique. If no ill effects are noted, you can continue to clean with the product and process tested.


9) RESTRICTIONS: Restrict the use of the surface to light traffic and non-harsh chemicals until the coating is fully cured (see technical data under full cure). It is best to let the floor remain dry for the full cure cycle. Dependent on actual complete system application, the surface may be slippery, especially when wet or contaminated; keep the surface clean and dry.

Preparation, Mixing and Installation Instructions for SPE-META-UV / 100% CLEAR EPOXY BINDER System. 


1.) PRODUCT STORAGE: Store product in an area so as to bring the material to normal room temperature before using. Continuous storage should be between 60 and 90 degrees F. Low temperatures or temperature fluctuations may cause crystallization.


2.) SURFACE PREPARATION: The most suitable surface preparation would be a fine brush blast (shot blast) to remove all laitance and provide a suitable profile. All dirt, foreign contaminants, oil, and laitance must be removed to assure a trouble free bond to the substrate. A test should be made to determine that the substrate (Concrete, Laminate, Tile, Formica, MDF, etc) is dry; this can be done by placing a 4’X4’ plastic sheet on the substrate and taping down the edges. If after 24 hours, the substrate is still dry below the plastic sheet, then the substrate is dry enough to start coating. The plastic sheet testing is also a good method to determine if any hydrostatic pressure problems exist that may later cause disbanding.


3.) PRODUCT MIXING: When mixing metallics take part B, open and pour into bucket, next open Metallic container and slowly pour into part B while mixing thoroughly. Make sure metallics achieve wetness. Once all metallics are mixed thoroughly add Part A and again mix thoroughly. To prevent air from being introduced into the epoxy, DO NOT lift mixing blade out of epoxy while mixing. This product has a mix ratio of 9.0# part A to 4.15# part B. Standard packages are in pre-measured kits and should be mixed as supplied in the kit. We highly recommend that the kits not be broken down unless suitable weighing equipment is available. After the two parts are combined, mix well with slow speed mixing equipment such as a jiffy mixer until the material is thoroughly mixed and streak free. After mixing, transfer the mixed material to another pail (the transfer pail) and again remix. The material in the transfer pail is now ready to be applied on the primed substrate. Improper mixing may result in product failure.


4.) PRIMING: A suitable primer should be used before applying this product. See the front side of this technical data for primer information. If a primer is not used, more porous substrates may cause outgassing and possible surface defects.


5.) PRODUCT APPLICATION: The mixed material can be applied by brush or roller. However, the material can also be applied by a suitable serrated squeegee and then back rolled as long as the appropriate thickness recommendations are maintained. Maintain temperatures and relative humidity within the recommended ranges during the application and curing process. If concrete conditions or over aggressive mixing causes air entrapment, then an air release roller tool should be used prior to the coating tacking off to remove the air entrapped in the coating. This product can be used with various colored sand in a broadcast system or other suitable aggregate can be used in conjunction with this product to achieve a variety of color and application patterns. When using as a broadcast binder, always evaluate performance parameters with a test area which is dependent on aggregate size and thickness, prior to application. Contact your representative for details as necessary.


6. RECOAT OR TOPCOATING: If you opt to recoat or topcoat this product, you must first be sure that the coating has tacked o before recoating. Always remember that colder temperatures will require more cure time for the product before recoating or top coating can commence. Before recoating or top coating, check the coating to ensure no epoxy blushes were developed (a whitish, greasy film or de-glossing). If a blush is present, it must be removed prior to top coating or recoating. Many epoxy coatings and urethanes are compatible for use as a topcoat for this product as well as multiple coats of this product.


7) CLEANUP: Use xylol.


8) CLEANING: Caution! Some cleaners may affect the color. Test each cleaner in a small area. If no ill effects are noted, you can continue to clean with the product and process tested.


9) RESTRICTIONS: Restrict the use of the epoxy to light traffic/use, and non-harsh chemicals until the coating is fully cured (see technical data under full cure). It is best to let the floor remain dry for the full cure cycle. Dependent on actual complete system application, the surface may be slippery, especially when wet or contaminated; keep the surface clean and dry.

Customer Review - Dave S. Metallic Epoxy for Warehouse and Commercial Floors - Spartan Epoxies

I can't say enough about my experience with Spartan Epoxies. I have a 6500 square ft airplane hangar that needed a floor. I chose a white base with all pearl metallic powder. Jeff and Bryan walked me thru the entire process. They even filmed a sample board for me and gave me the proper technique to achieve the look I was going for. Before we started, Spartan jumped on a call with myself and my helpers. They got everyone here that was involved in installing and gave us precise instructions. They got us organized, assigned jobs for each installer, answered every question, gave us confidence, and we got the job done with amazing results! Compared to other companies, I saved thousands and got a better product in my opinion. (I've used other online epoxy companies prior and payed double!). Thank you Spartan Epoxies! I plan on using their company for all of my projects from now on. 
Dave S. 


Customer Review - Jim P. Spartan Epoxies

Great product and easy to work with! I used the metallic system with a dark grey base coat and urethane top coat. This was done in a basement floor about 700 square ft. The floor came out awesome with the help of tech support and product ease of use.
Jim P. 


Customer Review - Caleb M. Spartan Epoxies Metallic Epoxy for Countertops

Couldn't be happier with this product as well as with the support and info I received from you guys... My countertops came out amazing. Couldn't believe I did them myself. Thanks again for all your help. I'll be looking forward to my next project with you now.
Caleb M. 

Related Products