ALL KITS ON SALE! Save Hundreds! Large Project? Request a Quote.
  • HP90 - Polyaspartic Sealer

HP90 - Polyaspartic Sealer

High Performance Polyaspartic Sealer / 107 – 160 square feet per gallon  HP90 is a two component 90% solids polyaspartic aliphatic polyaspartic sealer. This material can be used as the base coat and the topcoat over paint chip decorative b ...
  • $0.00

Available Options

High Performance Polyaspartic Sealer / 107 – 160 square feet per gallon 

HP90 is a two component 90% solids polyaspartic aliphatic polyaspartic sealer. This material can be used as the base coat and the topcoat over paint chip decorative broadcasts or colored sand broadcasts, and a metallic epoxy system to provide an infinite array of color schemes or patterns. HP90 has excellent chemical resistance, hardness, abrasion resistance, UV stability and has a good clear gardner color. The formulation has a longer working time, however, this product still has a quick tack free time for foot traffic (3 to 7 hours).


RECOMMENDED FOR:
Recommended for areas where a medium build broadcasted floor is desired and installation downtime is very limited. This material can also be applied over a broadcasted or troweled system as a thin to medium build sealer. Can also be used as a top coat on a variety of systems including metallic epoxy floors and counters.


CURE SCHEDULE: (70°F) (70% relative humidity)
pot life (to gel) – (150 gram mass)………………....greater than 2 hour
(Actual usable working time is approximately 20-25 minutes, depending on environmental conditions and volumes)
tack free (dry to touch)………………...……………………3-7 hours
recoat or topcoat.....…………….……..….................................5-8 hours
light foot traffic...………………………………................…6-8 hours
full cure (heavy traffic)... …………………..……..….......24-72 hours


APPLICATION TEMPERATURE:
50-90 degrees F with relative humidity below 85%


DOWNLOAD TECH DATA AND INSTRUCTIONS PDF

MIXING AND APPLICATION INSTRUCTIONS (SPE-HP90)


1.) PRODUCT STORAGE: Store product at normal room temperature before using. Continuous storage should be between 60 and 90 degrees F. Low temperature or temperature fluctuations may cause crystallization. 


2.) SURFACE PREPARATION: The most suitable surface preparation would be a brush blast (shot blast) to remove all laitance and provide a suitable profile. All dirt, foreign contaminants, oil and laitance must be removed to assure a trouble free bond to the substrate. A test should be made to determine that the concrete is dry; this can be done by placing a 4’X4’ plastic sheet on the substrate and taping down the edges. If after 24 hours, the substrate is still dry below the plastic sheet, then the substrate is dry enough to start coating. The plastic sheet testing is also a good method to determine if any hydrostatic pressure problems exist that may later cause disbonding. For applications directly over concrete, Testing should be performed to confirm a moisture vapor emission rate below 3 lb/24hr/1000 ft2 per ASTM F1869 


3.) PRODUCT MIXING: This product has a mix ratio of 12.7# part A to 9.2# part B. Standard packages are in pre-measured kits and should be mixed as supplied in the kit. After the two parts are combined, mix well with slow speed mixing equipment such as a jiffy mixer until the material is thoroughly mixed and streak free. After mixing, transfer the mixed material to another pail (the transfer pail) and again remix. The material in the transfer pail is now ready to be applied on the primed substrate. 


4.) PRIMING: A suitable primer should be used before applying this product. See the front side of this technical data for primer information. However, whether a primer is used or not, it is advisable to apply a test patch prior to using this product to determine if the adhesion characteristics are suitable for the service environment. 


5.) PRODUCT APPLICATION: The mixed material can be applied by brush, serrated squeegee, or roller. Maintain temperatures and relative humidity within the recommended ranges during the application and curing process. The product can be used as a topcoat to seal in the broadcasted paint chip or broadcasted quartz base for the final coat. Use an air release roller tool when needed. Improper mixing may result in product failure. It should be pointed out that relative humidity can have a dramatic influence on the curing characteristics. The product will dry quicker and have less working time when the relative humidity is higher while a lower relative humidity will lengthen the dry time and working time. Mix only an amount that can be applied in the time allotted. Be sure that any tie-ins to previously applied material is also within the recommended time allotted for use as the previously applied material may begin to tack off in a short period of time. 


6.) RECOAT OR TOPCOATING: This material can be applied in multiple layers to increase build or can also be used as the final topcoat to seal in the aggregate filled base system. If you opt to recoat or topcoat this product, you must first be sure that the coating has tacked off before recoating. Always remember that colder temperatures will require more cure time for the product before recoating or topcoating can commence. 


7.) CLEANUP: Use xylol 


8.) FLOOR CLEANING: Caution! Some cleaners may affect the color of the surface installed. Test each cleaner in a small area, utilizing your cleaning technique. If no ill effects are noted, you can continue to clean with the product and process tested. 


9.) RESTRICTIONS: Restrict the use of the floor to light traffic or counter with light use and non-harsh chemicals until the coating is fully cured (see technical data under full cure). It is best to let the floor / surface to remain dry for the full cure cycle. Dependent on actual complete system application, surface may be slippery, especially when wet or contaminated; keep surface clean and dry. 


SOLIDS BY WEIGHT: 90% (+/- 2%) 

SOLIDS BY VOLUME: 88% (+/-2%) 

VOLATILE ORGANIC CONTENT: Less than 100 grams per liter 

COLORS AVAILABLE: Clear – gardner color 1-2 

RECOMMENDED FILM THICKNESS: 

.10-15 mils. (when applying directly to concrete, precautions should be taken to properly prepare the substrate and the moisture content of the substrate should be tested. Do not apply to damp surfaces.) COVERAGE PER GALLON: 107 – 160 square feet per gallon 

PACKAGING INFORMATION

2.5 gallon kit (other special kit sizes are available upon request. (packaging information is approximate net volume) 

MIX RATIO: 12.70 pounds part A to 9.2 pounds part B. The mix ratio is approximately 1.5 gallons part A to 1 gallon part B. 

SHELF LIFE: 6 months in unopened containers 

FINISH CHARACTERISTICS: Gloss (>70 at 60 degrees @ glossmeter) 

COMPRESSIVE STRENGTH: 11,500 psi @ ASTM D695 

TENSILE STRENGTH: 3,800 psi @ ASTM D638 

ULTIMATE ELONGATION: 2.8% 

HARDNESS: Shore D= 30 

ABRASION RESISTANCE: Taber abraser CS-17 calibrase wheel with 1000 gram total load and 500 cycles= 20 mg loss 

ADHESION: 340 psi @ elcometer (concrete failure, no delamination, applied to shotblasted concrete) 

VISCOSITY: Mixed= 1,000-2,000 cps (typical) 

DOT CLASSIFICATIONS: Part A “UN1993, FLAMMABLE LIQUID N.O.S. (CONTAINS Xylene), 3, PG III 

Part B “UN1993, FLAMMABLE LIQUID N.O.S. (CONTAINS Xylene), 3, PG III 

CURE SCHEDULE: (70°F) (70% relative humidity) 

Pot life (to gel) – (150 gram mass)….….….…....Greater than 2 hours 

(Actual usable working time is approximately 20-25 minutes, depending on environmental conditions and volumes). 

Tack free (dry to touch)………………………………………3-7 hours 

Recoat or top oat .....……..…………………………….......... 5-8 hours 

Light Foot Traffic / Light Use ………………......................…6-8 hours 

Full cure (heavy traffic) ……..………..………..………..... 24-72 hours 

APPLICATION TEMPERATURE: 

50-90 degrees F with relative humidity below 85% 

MIXING AND APPLICATION INSTRUCTIONS (SPE-HP90)


1.) PRODUCT STORAGE: Store product at normal room temperature before using. Continuous storage should be between 60 and 90 degrees F. Low temperature or temperature fluctuations may cause crystallization. 


2.) SURFACE PREPARATION: The most suitable surface preparation would be a brush blast (shot blast) to remove all laitance and provide a suitable profile. All dirt, foreign contaminants, oil and laitance must be removed to assure a trouble free bond to the substrate. A test should be made to determine that the concrete is dry; this can be done by placing a 4’X4’ plastic sheet on the substrate and taping down the edges. If after 24 hours, the substrate is still dry below the plastic sheet, then the substrate is dry enough to start coating. The plastic sheet testing is also a good method to determine if any hydrostatic pressure problems exist that may later cause disbonding. For applications directly over concrete, Testing should be performed to confirm a moisture vapor emission rate below 3 lb/24hr/1000 ft2 per ASTM F1869 


3.) PRODUCT MIXING: This product has a mix ratio of 12.7# part A to 9.2# part B. Standard packages are in pre-measured kits and should be mixed as supplied in the kit. After the two parts are combined, mix well with slow speed mixing equipment such as a jiffy mixer until the material is thoroughly mixed and streak free. After mixing, transfer the mixed material to another pail (the transfer pail) and again remix. The material in the transfer pail is now ready to be applied on the primed substrate. 


4.) PRIMING: A suitable primer should be used before applying this product. See the front side of this technical data for primer information. However, whether a primer is used or not, it is advisable to apply a test patch prior to using this product to determine if the adhesion characteristics are suitable for the service environment. 


5.) PRODUCT APPLICATION: The mixed material can be applied by brush, serrated squeegee, or roller. Maintain temperatures and relative humidity within the recommended ranges during the application and curing process. The product can be used as a topcoat to seal in the broadcasted paint chip or broadcasted quartz base for the final coat. Use an air release roller tool when needed. Improper mixing may result in product failure. It should be pointed out that relative humidity can have a dramatic influence on the curing characteristics. The product will dry quicker and have less working time when the relative humidity is higher while a lower relative humidity will lengthen the dry time and working time. Mix only an amount that can be applied in the time allotted. Be sure that any tie-ins to previously applied material is also within the recommended time allotted for use as the previously applied material may begin to tack off in a short period of time. 


6.) RECOAT OR TOPCOATING: This material can be applied in multiple layers to increase build or can also be used as the final topcoat to seal in the aggregate filled base system. If you opt to recoat or topcoat this product, you must first be sure that the coating has tacked off before recoating. Always remember that colder temperatures will require more cure time for the product before recoating or topcoating can commence. 


7.) CLEANUP: Use xylol 


8.) FLOOR CLEANING: Caution! Some cleaners may affect the color of the surface installed. Test each cleaner in a small area, utilizing your cleaning technique. If no ill effects are noted, you can continue to clean with the product and process tested. 


9.) RESTRICTIONS: Restrict the use of the floor to light traffic or counter with light use and non-harsh chemicals until the coating is fully cured (see technical data under full cure). It is best to let the floor / surface to remain dry for the full cure cycle. Dependent on actual complete system application, surface may be slippery, especially when wet or contaminated; keep surface clean and dry. 


SOLIDS BY WEIGHT: 90% (+/- 2%) 

SOLIDS BY VOLUME: 88% (+/-2%) 

VOLATILE ORGANIC CONTENT: Less than 100 grams per liter 

COLORS AVAILABLE: Clear – gardner color 1-2 

RECOMMENDED FILM THICKNESS: 

.10-15 mils. (when applying directly to concrete, precautions should be taken to properly prepare the substrate and the moisture content of the substrate should be tested. Do not apply to damp surfaces.) COVERAGE PER GALLON: 107 – 160 square feet per gallon 

PACKAGING INFORMATION

2.5 gallon kit (other special kit sizes are available upon request. (packaging information is approximate net volume) 

MIX RATIO: 12.70 pounds part A to 9.2 pounds part B. The mix ratio is approximately 1.5 gallons part A to 1 gallon part B. 

SHELF LIFE: 6 months in unopened containers 

FINISH CHARACTERISTICS: Gloss (>70 at 60 degrees @ glossmeter) 

COMPRESSIVE STRENGTH: 11,500 psi @ ASTM D695 

TENSILE STRENGTH: 3,800 psi @ ASTM D638 

ULTIMATE ELONGATION: 2.8% 

HARDNESS: Shore D= 30 

ABRASION RESISTANCE: Taber abraser CS-17 calibrase wheel with 1000 gram total load and 500 cycles= 20 mg loss 

ADHESION: 340 psi @ elcometer (concrete failure, no delamination, applied to shotblasted concrete) 

VISCOSITY: Mixed= 1,000-2,000 cps (typical) 

DOT CLASSIFICATIONS: Part A “UN1993, FLAMMABLE LIQUID N.O.S. (CONTAINS Xylene), 3, PG III 

Part B “UN1993, FLAMMABLE LIQUID N.O.S. (CONTAINS Xylene), 3, PG III 

CURE SCHEDULE: (70°F) (70% relative humidity) 

Pot life (to gel) – (150 gram mass)….….….…....Greater than 2 hours 

(Actual usable working time is approximately 20-25 minutes, depending on environmental conditions and volumes). 

Tack free (dry to touch)………………………………………3-7 hours 

Recoat or top oat .....……..…………………………….......... 5-8 hours 

Light Foot Traffic / Light Use ………………......................…6-8 hours 

Full cure (heavy traffic) ……..………..………..………..... 24-72 hours 

APPLICATION TEMPERATURE: 

50-90 degrees F with relative humidity below 85%